savgroup.ae

Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Kiilto KeraSafe Speed A + X

Adhesive for KeraSafe+ foil

A fast, two-component, cement-based adhesive for installing Kiilto KeraSafe+ foil. Suitable also for sealing foil overlap joints and installing Kiilto reinforcement sheets and prefabricated corner pieces. ETAG-approved with Kiilto KeraSafe+ foil.

Special features

 

  • very fast, good spreading properties, suitable for installing the waterproofing foil as well as making inlets and sealing overlaps
  • adhesive for installing Kiilto KeraSafe+ foil
  • ready to be tiled: walls approx. 1 h, floors 2 h after installation of Kiilto KeraSafe+ foil

Materials

Application

Kiilto KeraSafe Speed is a two-component adhesive suitable for installing KeraSafe wet room foil using a roller or brush.

Package Size

5 + 3,3 kg

EAN Code

6411513752159

Application temperature

+10°C -+25 °C

Coatable

Walls: Immediately after installing KeraSafe foil (start tiling from the same edge as KeraSafe installation).
Floors: 2 h after installing KeraSafe foil

Coverage

approx. 600 g/m²

Density/specific weight

1.2 kg/l

Frost resistance

Liquid component freezes

Mixing ratio

60 (liquid) 40 (powder)

Mixture colour

Light pink (when wet)
Dark brown (after drying)

Open time

10–15 min primed substrate,
unprimed substrate <10 min

Package sizes

8.33 kg (5 kg liquid + 3.33 kg powder)

Pot life

approx. 60 min

Storage

In unopened containers, above +1 °C, for 1 year.

Substrate humidity

< 90 %

Temperature resistance when dry

-20°C -+70 °C

Type/binder

Styrene acrylate (liquid) and cement (powder)

Instructions for use

 

Mixing:
Shake the liquid. Pour it into the empty mixing container and sprinkle the powder component into the liquid while mixing. Carefully mix the liquid and the powder (mixing ratio 60:40 by weight) until an even mass is formed. The pot-life of the mixture is approx. 60 minutes – so mix only the amount that can be used within that time. Do not dilute a mixture that has started to harden.

Walls:
If needed, sand and/or smooth uneven substrates with a Kiilto wall plaster suitable under waterproofing and tiling. Prior to KeraSafe installation, prime the dry wall with diluted – 1:1 Kiilto Keraprimer, if necessary. Note: Priming will lengthen the open time of Kiilto KeraSafe Speed after application. Allow the primer to dry for about 1 hour before installing KeraSafe. Apply Kiilto KeraSafe Speed on angles, corners and wall surface of an area that can be covered by one piece of foil. Place KeraSafe foil in position and see that in corners the foil folds 5 cm over to the next wall and 5 cm over the floor. Press the foil tightly onto the substrate and rub into position with a rigid plastic trowel so that all air is pressed out and the foil is fully adhered to the substrate. Use Kiilto KeraSafe Speed for gluing the lap joints of the foils.

Floors:
If necessary, sand and/or smooth uneven substrates with Kiilto floor levelling compound. Prior to KeraSafe installation, prime the dry floor with diluted – 1:1 Kiilto Keraprimer, if necessary. Allow the primer to dry for about 1 hour before installing KeraSafe. Install self-adherent Kiilto KeraSafe drain reinforcement on the floor drain. Apply Kiilto KeraSafe Speed on the floor, lap joints and over the floor drain reinforcement sheet. Roll out the foil, and press into position to get all the air out. Apply Kiilto KeraSafe Speed around inlets and press suitable inlet reinforcements into position. Glue the pre-fabricated corner reinforcement pieces in place with Kiilto KeraSafe Speed. Apply Speed adhesive also on inlet reinforcement pieces and corner pieces. Before tiling, cut a hole (approx. 60 mm smaller than the diameter of the drain) for the floor drain in the foil, and mount the clamp ring.

Additional information

The information given in this product data sheet is based on our tests and our practical knowledge. The technical data is defined in standard conditions. Variations in local working conditions and methods will affect the product performance and result. Lopputulokseen vaikuttaa merkittävästi myös työn suoritustapa. We guarantee the high quality of our products according to our Quality Management System. No liability can be accepted from incorrect use of the product, or due to prevailing conditions we have no control over. Therefore, we cannot be held responsible for the final result. The correct use of the product presupposes that the user has made him/herself aware of the contents of the working instructions and procedure guide, if provided.

Environment and safety

Avoid unnecessary skin contact and exposure with the fresh product, use safety gloves. Please refer to the material safety data sheet. For more information about the product and package disposal, go to www.kiilto.com.

Discover More

Certificates

Open chat
Hello
Can we help you?