savgroup.ae

Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Kiilto 97 DF

Smoothing compound

Dust reduced, self-levelling smoothing compound for floors before laying the floor covering. Low alkali.

Special features

 

  • dust reduced, self-levelling, pumpable, paintable
  • fine smoothing of floors
  • coverage 1.6 kg/m²/mm
  • walkable: 4 h
  • coatable: 24 h
  • interior areas

Materials

Application

Suitable for levelling floor surfaces at thicknesses 1-7 mm before laying the floor covering.

The substrate must be clean, solid and firm. Remove cement laitance, paint splashes, adhesive residue and other impurities and vacuum the floor properly.

Concrete subfloors are pre-treated with 1:4 diluted Kiilto Start or PrimerOne primer (20% Kiilto Primer / 80 % water) prior to floor screed. Surfaces under reconstruction as well as board surfaces must be primed with undiluted Kiilto Start Primer or PrimerOne before levelling. Non-absorbent substrates, such as ceramic tiles or painted surfaces, can also be treated with Kiilto Fix Primer.

A low alkaline screed layer protects the adhesive and vinyl coating from the damage caused by alkaline moisture in the concrete. The studies have shown that a 5 mm thick screed layer provides the protective effect.

The concrete substrate must comply with national standards.

Package Size

20 kg

EAN Code

6411512079202

Application temperature

Optimal +18–23 °C, minimum +10 °C

Bond strength

> 1.5 MPa, EN 13813

Classifications and certificates

CT-C30-F7 (EN13813), M1

Coatable

7 mm / 24 h ( 23 ºC, 50 % RH )

Compression strength

C30 (> 30 MPa), EN 13813

Coverage

1 mm layer/m² solid matter weighs approx. 1.6 kg (approx. 12 litres of screed/bag).

Fire class

A2fl-s1

Flexural strength

F7 (> 7 MPa), EN 13813

Layer thickness

1–7 mm

Max. grain size

0.3 mm

Mixing ratio

5.2–5.6 l water / 20 kg bag

Package sizes

20 kg bag

Shrinkage

< 0,6 ‰ ( 23 °C, 50 % RH )

Storage

In an unopened package max. 1 year in dry conditions.

Substrate humidity

concrete < 90 % RH

Type/binder

Polymer-special cement-limestone-quarzt-based powder

Viscosity

Flow rate 150–160 mm, EN 12706

Walkable

approx. 4 hours ( 23 ºC, 50 % RH )

Working time

Approx. 20 min ( 23 ºC, 50 % RH )

pH

< 11 (low alkali)

Instructions for use

Fill the mixing container with the required amount of clean water. Strew Kiilto 97 DF -powder slowly while stirring in cool (+10–25 °C), clean water until a smooth, flexible mass is formed. Let the mix mature for approx. 2 min and then remix once before use.

Apply the smoothing compound evenly by using a steel or notched trowel. It can be applied also by an appropriate floor screed pump. The layer must be dry before applying a new one.

The drying of the smoothing compound must not be accelerated e.g. by heat or ventilation, since too fast drying may cause hair cracks. If the temperature in the levelled room is higher than normally, the relative humidity very low, or if the levelled floor surface is exposed to direct sunlight, we recommend covering the floor with a tarpaulin as soon as it is dry enough to allow walking. The floor should be covered with a flooring relatively soon after it has hardened and dried. This will prevent the surface from over drying, cracking and loosening.

Suitable also for floors to be painted in secondary rooms with light traffic, but not for example for garages or bathrooms floors etc.

In areas where waterproofing is used, for example bathroom floors, floor levelling should be applied under the waterproofing membrane.

Not suitable for areas permanently under water (e.g. swimming pools).

Note! Avoid excessive use of water, since it will weaken the surface strength and may cause separation and cracking.

Additional information

The information given in this product data sheet is based on our tests and our practical knowledge. The technical data is defined in standard conditions. Variations in local working conditions and methods will affect the product performance and result. The result is also strongly affected by working methods. We guarantee the high quality of our products according to our Quality Management System. No liability can be accepted from incorrect use of the product or prevailing conditions, over which we have no control. Thus, we cannot be held responsible for the final result. To use the product properly, please read the product brochure, work instructions and the safety data sheet available at www.kiilto.com.

Environment and safety

Avoid unnecessary skin contact and exposure with the fresh product, use safety gloves. Refer to the material safety data sheet. For information on product and package disposal, visit www.kiilto.com.

Discover More

Certificates

Open chat
Hello
Can we help you?